WOUND ROTOR DOUBLY FED INDUCTION MACHINE WITH RADIAL ROTARY TRANSFORMER
DOI:
https://doi.org/10.1590/S2179-10742013000200013Keywords:
Alternating current machines, brushless machines, prototypes, rotary transformer, transformer calculationAbstract
This paper shows a wound rotor doubly fed induction machine in which the typical brushes and slip-rings are substituted by rotary transformers. The advantages of rotary transformer usage, the doubly fed induction machine operation and the dimensioning of a radial rotary transformer are the main aspects presented in this study. The use of analytical equations is a very interesting resource for the development of industrial software for the calculation of this kind of device. Comparison between simulated and measured results shows the good approximation of the steady-state model with the reality of this equipment.
References
[1] M. Ruviaro, F. Rüncos, N. Sadowski, I. M. Borges, “Analysis and Tests Results of a Brushless Doubly Fed Induction
Machine with Rotary Transformer”, IEEE Transactions on Industrial Electronics, Early Access, 2011.
[2] M. Ruviaro, F. Rüncos, N. Sadowski, I. M. Borges, “Design and Analysis of a Brushless Doubly Fed Induction
Machine with Rotary Transformer”, in XIX International Conference on Electrical Machines (ICEM), Rome, Italy,
2010.
[3] M. Ruviaro, “Three-Phase Wound Rotor Asynchronous Machine Doubly Fed by Rotary Transformer” (in Portuguese),
Master’s dissertation, Universidade Federal de Santa Catarina, Brazil, 2011.
[4] F. Rüncos, “Double-Fed in Cascade Brushless Three-Phase Asynchronous Machine” (in Portuguese), Master’s
dissertation, Universidade Federal de Santa Catarina, Brazil, 2001.
[5] F. Rüncos, “Modeling, Project and Analysis of Brushless Double-Fed Three-Phase Asynchronous Machine” (in
Portuguese), Doctoral thesis, Universidade Federal de Santa Catarina, Brazil, 2006.
[6] N. Patin, E. Monmasson, J.-P. Louis, "Modeling and Control of a Cascaded Doubly Fed Induction Generator Dedicated
to Isolated Grid", IEEE Transactions on Industrial Electronics, vol. 56, no. 10, pp. 4207-4219, Oct 2009.
[7] S. Williamson, A. C. Ferreira, A. K. Wallace, “Generalised Theory of the Doubly-Fed Machine. Part 1: Analysis”,
IEE Proceedings Electrical Power Application, vol. 144, n. 2, pp. 111-122, Mar 1997.
[8] S. Williamson, A. C. Ferreira, “Generalised Theory of the Doubly-Fed Machine. Part 2: Model Verification and
Performance”, IEE Proceedings Electrical Power Application, vol. 144, n. 2, pp. 123-129, Mar 1997.
[9] S. H. Marx, R. W. Rounds, “A Kilowatt Rotary Power Transformer”, IEEE Transactions on Aerospace and Electronic
Systems, vol. AES-7, issue 6, pp. 1157-1163, Nov. 1971.
[10] J. Legranger, G. Friedrich, S. Vivier, J. C. Mipo, “Comparison of Two Optimal Rotary Transformer Designs for Highly
Constrained Applications”, in Proc IEEE Electric Machines & Drives Conference (IEMDC), pp. 1546-1515, 2007.
[11] K.D. Papastergiou, D.E. Macpherson, "An Airborne Radar Power Supply With Contactless Transfer of Energy—Part I:
Rotating Transformer", IEEE Transactions on Industrial Electronics, vol. 54, no. 5, pp. 2874-2884, Oct 2007.
[12] K.D. Papastergiou, D.E. Macpherson, "An Airborne Radar Power Supply With Contactless Transfer of Energy—Part
II: Converter Design", IEEE Transactions on Industrial Electronics, vol. 54, no. 5, pp. 2885-2893, Oct 2007.
[13] K.D. Papastergiou, D.E. Macpherson, "Contact-less Transfer of Energy by means of a rotating transformer", in Proc.
IEEE International Symposium on Industrial Electronics, pp. 1735-1740, 2005.
[14] K.D. Papastergiou, D.E. Macpherson, “Air-gap effects in inductive energy transfer”, IEEE Power Electronics
Specialists Conference, pp. 4092-4097, 2008.
[15] T.A. K. Stuart, H. R.J. Shamseddin, “Rotary Transformer Design with Fixed Magnetizing and/or Leakage Inductances”,
IEEE Transactions on Aerospace and Electronic Systems, AES-22, pp. 565, Sep 1986.
[16] J.P.C. Smeets, L. Encica, E.A. Lomonova, “Comparison of winding topologies in a pot core rotating transformer”,
presented at 12th International Conference on Optimization of Electrical and Electronic Equipment (OPTIM), Brasov,
Romania, 2010.
[17] J. Legranger, G. Friedrich, S. Vivier, J. C. Mipo, “Design of a Brushless Rotor Supply for a Wound Rotor Synchronous
Machine for Integrated Starter Generator”, in Proc IEEE Vehicle Power and Propulsion Conference, pp. 236-241,
2007.
[18] C. Wm. T. McLyman, “Transformer and Inductor Design Handbook”, 3
rd ed., Chapter 19, Ed. New York: Marcel
Dekker Inc., 2004.
Machine with Rotary Transformer”, IEEE Transactions on Industrial Electronics, Early Access, 2011.
[2] M. Ruviaro, F. Rüncos, N. Sadowski, I. M. Borges, “Design and Analysis of a Brushless Doubly Fed Induction
Machine with Rotary Transformer”, in XIX International Conference on Electrical Machines (ICEM), Rome, Italy,
2010.
[3] M. Ruviaro, “Three-Phase Wound Rotor Asynchronous Machine Doubly Fed by Rotary Transformer” (in Portuguese),
Master’s dissertation, Universidade Federal de Santa Catarina, Brazil, 2011.
[4] F. Rüncos, “Double-Fed in Cascade Brushless Three-Phase Asynchronous Machine” (in Portuguese), Master’s
dissertation, Universidade Federal de Santa Catarina, Brazil, 2001.
[5] F. Rüncos, “Modeling, Project and Analysis of Brushless Double-Fed Three-Phase Asynchronous Machine” (in
Portuguese), Doctoral thesis, Universidade Federal de Santa Catarina, Brazil, 2006.
[6] N. Patin, E. Monmasson, J.-P. Louis, "Modeling and Control of a Cascaded Doubly Fed Induction Generator Dedicated
to Isolated Grid", IEEE Transactions on Industrial Electronics, vol. 56, no. 10, pp. 4207-4219, Oct 2009.
[7] S. Williamson, A. C. Ferreira, A. K. Wallace, “Generalised Theory of the Doubly-Fed Machine. Part 1: Analysis”,
IEE Proceedings Electrical Power Application, vol. 144, n. 2, pp. 111-122, Mar 1997.
[8] S. Williamson, A. C. Ferreira, “Generalised Theory of the Doubly-Fed Machine. Part 2: Model Verification and
Performance”, IEE Proceedings Electrical Power Application, vol. 144, n. 2, pp. 123-129, Mar 1997.
[9] S. H. Marx, R. W. Rounds, “A Kilowatt Rotary Power Transformer”, IEEE Transactions on Aerospace and Electronic
Systems, vol. AES-7, issue 6, pp. 1157-1163, Nov. 1971.
[10] J. Legranger, G. Friedrich, S. Vivier, J. C. Mipo, “Comparison of Two Optimal Rotary Transformer Designs for Highly
Constrained Applications”, in Proc IEEE Electric Machines & Drives Conference (IEMDC), pp. 1546-1515, 2007.
[11] K.D. Papastergiou, D.E. Macpherson, "An Airborne Radar Power Supply With Contactless Transfer of Energy—Part I:
Rotating Transformer", IEEE Transactions on Industrial Electronics, vol. 54, no. 5, pp. 2874-2884, Oct 2007.
[12] K.D. Papastergiou, D.E. Macpherson, "An Airborne Radar Power Supply With Contactless Transfer of Energy—Part
II: Converter Design", IEEE Transactions on Industrial Electronics, vol. 54, no. 5, pp. 2885-2893, Oct 2007.
[13] K.D. Papastergiou, D.E. Macpherson, "Contact-less Transfer of Energy by means of a rotating transformer", in Proc.
IEEE International Symposium on Industrial Electronics, pp. 1735-1740, 2005.
[14] K.D. Papastergiou, D.E. Macpherson, “Air-gap effects in inductive energy transfer”, IEEE Power Electronics
Specialists Conference, pp. 4092-4097, 2008.
[15] T.A. K. Stuart, H. R.J. Shamseddin, “Rotary Transformer Design with Fixed Magnetizing and/or Leakage Inductances”,
IEEE Transactions on Aerospace and Electronic Systems, AES-22, pp. 565, Sep 1986.
[16] J.P.C. Smeets, L. Encica, E.A. Lomonova, “Comparison of winding topologies in a pot core rotating transformer”,
presented at 12th International Conference on Optimization of Electrical and Electronic Equipment (OPTIM), Brasov,
Romania, 2010.
[17] J. Legranger, G. Friedrich, S. Vivier, J. C. Mipo, “Design of a Brushless Rotor Supply for a Wound Rotor Synchronous
Machine for Integrated Starter Generator”, in Proc IEEE Vehicle Power and Propulsion Conference, pp. 236-241,
2007.
[18] C. Wm. T. McLyman, “Transformer and Inductor Design Handbook”, 3
rd ed., Chapter 19, Ed. New York: Marcel
Dekker Inc., 2004.
Downloads
Published
2013-08-01
How to Cite
Maurício Ruviaro, Fredemar Rüncos, & Nelson Sadowski. (2013). WOUND ROTOR DOUBLY FED INDUCTION MACHINE WITH RADIAL ROTARY TRANSFORMER. Journal of Microwaves, Optoelectronics and Electromagnetic Applications (JMOe), 12(2), 411–426. https://doi.org/10.1590/S2179-10742013000200013
Issue
Section
Regular Papers
